Platoro Dam: Constructed 1949-19511954 - Dams - 71 pages |
From inside the book
Results 1-5 of 8
Page 5
... included 12 test pits excavated in each area by a small dragline . For specifications purposes , the two areas were combined into one borrow area designated " borrow area A. Vegetation in the impervious area consisted of light scattered ...
... included 12 test pits excavated in each area by a small dragline . For specifications purposes , the two areas were combined into one borrow area designated " borrow area A. Vegetation in the impervious area consisted of light scattered ...
Page 7
... included provision for a fish screen at the inlet to the outlet works . Study of the 1946 designs and estimates resulted in a decision to eliminate the fish screen and to set the reservoir capacity at an intermediate value of 67,000 ...
... included provision for a fish screen at the inlet to the outlet works . Study of the 1946 designs and estimates resulted in a decision to eliminate the fish screen and to set the reservoir capacity at an intermediate value of 67,000 ...
Page 10
... included in the specifications . Below elevation 9965 , the crest of the permanent coffer- dam , rockfill was permitted in lieu of riprap . Instead of using the downstream rock source , the contractor requested and received permission ...
... included in the specifications . Below elevation 9965 , the crest of the permanent coffer- dam , rockfill was permitted in lieu of riprap . Instead of using the downstream rock source , the contractor requested and received permission ...
Page 15
... included a statement that a conduit should be used . Lay- outs were made with a conduit on each abutment near the river channel . It was impossi- ble to get a suitable alinement without excessive cuts near the downstream toe of the dam ...
... included a statement that a conduit should be used . Lay- outs were made with a conduit on each abutment near the river channel . It was impossi- ble to get a suitable alinement without excessive cuts near the downstream toe of the dam ...
Page 17
... included in cost of in- stalling supports or liner plates Concrete pipe supports @ 36 " : crs UNITED STATED DEPARTMENT OF THE INTERIOR BUREAU OF RECLAMATION SAN LUIS VALLEY PROJECT - COLORADO PLATORO DAM OUTLET WORKS PLAN , PROFILE AND ...
... included in cost of in- stalling supports or liner plates Concrete pipe supports @ 36 " : crs UNITED STATED DEPARTMENT OF THE INTERIOR BUREAU OF RECLAMATION SAN LUIS VALLEY PROJECT - COLORADO PLATORO DAM OUTLET WORKS PLAN , PROFILE AND ...
Common terms and phrases
48-inch butterfly valves acre-feet andesite axis Bolt bulldozed butterfly valves cofferdam completed Concrete grout conduit Conejos River contract cost cubic feet cubic yards cutoff trench dam and dike dam embankment dam foundation dike section discharge drain emergency gate end-dump trucks engineer equipment excavation fault fault gouge feet per second Figure fill zone flange flow fractured gate chamber Government camp grout cap Grout holes haul impervious material inches installation joints July Aug Sept June 21 laboratory leaf-Class left abutment load located main dam maximum Metal metalwork mixer moisture Order for changes outlet pipe outlet tunnel PARTIAL RUNOFF percent placed placement plates Platoro Dam pounds per square pumpcrete machine right abutment Rio Grande Compact RIO GRANDE COUNTY riprap ROCK BORROW AREA rockfill SAN LUIS VALLEY separation plant SLIDE ROCK BORROW specifications spillway bridge support rings talus tests trashrack structure unit valve house zone 1 material
Popular passages
Page 18 - ... PARTS 151. Character of Structure.— The structure is to be of the skeleton, curtain-beam type, resting on I-beam footings or grillages. The building is to be (18) stories high, with a basement story and a (flat) (mansard) (pointed) (hipped) roof. 152. Floor Loading.— The floors are to be calculated for a live load of (100) pounds per square foot, and a dead load of (50) pounds per square foot. The roof is to be calculated for a live load of (50) pounds per square foot, and a dead load of...
Page 22 - Specifications for Low and Intermediate Tensile Strength Carbon-Steel Plates of Flange and Firebox Qualities (Plates 2 in. and Under in Thickness) (ASTM Designation: A 285),' or Tentative Specifications for Low and Intermediate Tensile Strength Carbon-Steel Plates of Structural Quality (Plates 2 in.
Page 22 - Standard Specifications for FORGED- OR ROLLED-STEEL PIPE FLANGES, FORGED FITTINGS, AND VALVES AND PARTS FOR HIGH-TEMPERATURE SERVICE...