Trenton Dam: Constructed 1949-1953 |
From inside the book
Results 1-5 of 24
Page
... surface elevation 2785.6 ( as determined by model studies ) Gates : Three , 42 by 30 feet Stilling basin : Reinforced concrete with dentated ... water elevation 2705.0 20.58 AERIAL VIEW OF TRENTON DAM SPILLWAY DURING DEDICATION CEREMONIES.
... surface elevation 2785.6 ( as determined by model studies ) Gates : Three , 42 by 30 feet Stilling basin : Reinforced concrete with dentated ... water elevation 2705.0 20.58 AERIAL VIEW OF TRENTON DAM SPILLWAY DURING DEDICATION CEREMONIES.
Page 9
... Water jet holes CH21 21 to 3 Drive and drill holes DHI 6 " Denison sample holes . TPI 4'16'Hand dug test pits . Shale surface determined by ramming D. steel rod from bottom of jet hole Groundwater elevation at given date . SAND , silty ...
... Water jet holes CH21 21 to 3 Drive and drill holes DHI 6 " Denison sample holes . TPI 4'16'Hand dug test pits . Shale surface determined by ramming D. steel rod from bottom of jet hole Groundwater elevation at given date . SAND , silty ...
Page 15
... Water surface elevation 2752.0 to 2773.0 Storage , acre - feet 133,800 ( initially ) Irrigation storage 2710.0 to 2752.0 Dead storage ( normal water surface ) Streambed to 2710.0 ( invert of canal outlet ) Total storage to elevation ...
... Water surface elevation 2752.0 to 2773.0 Storage , acre - feet 133,800 ( initially ) Irrigation storage 2710.0 to 2752.0 Dead storage ( normal water surface ) Streambed to 2710.0 ( invert of canal outlet ) Total storage to elevation ...
Page 16
... ELEVATION IN FEET 2776 2780 2784 2788 2792 INFLOW HYDROGRAPH SPILLWAY DESIGN FLOOD- ( From Hydrology Branch Plate 10 ... water surfaces above El . 2773.0 with a ratio of reservoir water surface rise to gate cable travel of 1 : 5 . Discharge ...
... ELEVATION IN FEET 2776 2780 2784 2788 2792 INFLOW HYDROGRAPH SPILLWAY DESIGN FLOOD- ( From Hydrology Branch Plate 10 ... water surfaces above El . 2773.0 with a ratio of reservoir water surface rise to gate cable travel of 1 : 5 . Discharge ...
Page 22
... elevation of shale bedrock in the cutoff trench , 100 feet in height above ... surface of zone 2 material was extended from eleva- tion 2710 to about ... water surface and diminishing to 2 feet of riprap on a 12 - inch bedding at the dam ...
... elevation of shale bedrock in the cutoff trench , 100 feet in height above ... surface of zone 2 material was extended from eleva- tion 2710 to about ... water surface and diminishing to 2 feet of riprap on a 12 - inch bedding at the dam ...
Other editions - View all
Common terms and phrases
abutment acre-feet aggregate backfill Berm blanket blockouts Brass Cap BUREAU OF RECLAMATION camber canal outlet cement centerline chute coarse concrete construction Contraction joint contractor control house crushed rock cubic yards cutoff trench dam embankment dam foundation designed discharge eleva emergency gate chamber Figure Float flood control gravel grout high-pressure gates Highway bridge Hitchcock County holes horizontal hydraulic hydrostatic head inlet intake structure layer Limits of special loads located loess material maximum metal Nebr north borrow operation pier Pierre shale piezometer Pipe handrail pounds per square pozzolan PROJ pump radial gate railroad reinforcement relocation Republican River reservoir water surface riprap River outlet Rolled embankment SCALE OF FEET second-feet Settlement point Shale surface SILT silty slope south borrow area special compaction specifications spillway structure steel stilling basin storage Sump Sump pump surface at elevation tests Trenton Dam upstream valve vertical walls water surface elevation
Popular passages
Page 51 - Design, Construction, Inspection and Repair of Unfired Pressure Vessels for Petroleum Liquids and Gases.
Page 99 - yd. cu. yd. lin. ft. lin. ft. lin. ft. Labor and materials by contractor Unit cost
Page 94 - yd. cu. yd. cu. yd. cu. yd. Labor and materials by contractor Unit cost
Page 96 - ft. lin. ft. lin. ft. lin. ft. Labor and materials by contractor Unit cost
Page 100 - cu. yd. Lump sum Lump sum Labor and materials by contractor Unit cost 2.00
Page 99 - 88 89 90 91 92 93 94 Property and pay item description Installing metal pipe, fittings, and valves less than 6 inches in diameter Installing metal pipe, fittings, and valves 6 inches
Page 25 - above the maximum water surface, to prevent the dam from being overtopped by waves. Factors influencing wave height and wave ride-up, including maximum wind velocity, direction and duration, offshore reservoir
Page 98 - ft. Ib. Ib. Ib. Ib. Ib. Ib. Ib. Labor and materials by contractor Unit cost